13429100057

浙江省建德市洋溪街道新安江路909号

新闻中心 / NEWS

行业资讯

  • 不锈钢罐怎么样维护
  • 本站编辑:杭州新泰化工机械有限公司发布日期:2020-01-09 20:34 浏览次数:

不锈钢罐的运用首要包括查看工作,操作过程,修理保养及留意事项,详细过程见如下。

  1、查看准备工作

  1.1点动拌和电机,查看有无异常动静及漏油现象。

  1.2查看各阀门封闭是否紧密,查看密封体系,防止漏油。

  1.3查看电器是否完好,有无漏电现象。

  1.4查看安全阀、压力表、温度表、真空表等是否完好。

  2、配料罐运用操作过程

  2.1翻开真空阀门,待真空度到达-0.04Mpa时翻开进料口阀门,按工艺利用真空抽入前处理好的料液。

  2.2翻开进水阀门,抽入纯化水至工艺要求,翻开排气阀,破真空。

  2.3开启总电源开关,翻开拌和电机开关,进行拌和混匀。此刻翻开手孔进行投入固体粉料。增加结束,封闭,继续拌和。

  2.4药液需加热时,翻开夹套蒸汽阀门,同时翻开疏水阀,压力控制在0.10 Mpa以下,不用时封闭蒸汽阀,再关疏水阀。

  2.5药液冷却时,翻开夹套底部进水阀和出水阀进行冷却,不需要时封闭进水阀和出水阀,运用结束后及时清洗。

  2.6留意压力表压力,使之保持在0.1Mpa,到达加热要求封闭蒸汽阀门。

  2.7拌和混合结束封闭电机开关,封闭电源总闸,翻开放料阀进行放料。

  3、修理保养

  3.1常常查看焊缝、管路、液位计、阀门及人孔的气密性。

  3.2常常查看温度计、压力表的活络度。

  3.3查看安全阀是否活络,疏水阀是否畅通。

  3.4大修周期为一年,大修时一切传动部件滚动轴承需更换时,应及时更换,加注黄油润滑后,盖上注油孔。

  4、留意事项

  4.1设备运行出现故障,应将罐内余汽排尽,不能带压修理。

  4.2修理时,防止液体溅到电机上。

  4.3设备运用结束及时进行清洗。


The operation of stainless steel tank mainly includes the inspection work, operation process, repair and maintenance and matters needing attention. The detailed process is as follows. 1, check the preparation 1.1 point mixing motor, see if there is abnormal movement and oil leakage phenomenon. 1.2 check the tightness of each valve and check the sealing system to prevent oil leakage. 1.3 check electrical appliances are in good condition, there is no leakage phenomenon. Check whether the safety valve, pressure gauge, temperature gauge, vacuum gauge, etc. are in good condition. 2. Batch tank operation process 2.1 turn over the vacuum valve, when the vacuum reaches-0.04 MPA, turn over the inlet valve, according to the process of using the vacuum to pump the pre-processed liquid. 2.2 open the inlet valve, pump purified water to process requirements, open the exhaust valve, break the vacuum. 2.3 turn on the main power switch, turn on the mixer motor switch and mix well. Now Open the hand hole to put solid powder. Add End, seal, and continue mixing. 2.4 when the liquid medicine needs to be heated, open the jacket steam valve, open the trap at the same time, the pressure is controlled below 0.10 MPA, when not in use, close the steam valve, then close the trap. 2.5 when the medicine liquid cools, open the bottom water inlet valve and the water outlet valve of the jacket for cooling, close the water inlet valve and the water outlet valve when it is not needed, and clean it in time after use. 2.6 pay attention to the pressure of the pressure gauge so that it is kept at 0.1 MPA, to reach the heating requirements closed steam valve. 2.7 mixing the end of the closed motor switch, closed the power master brake, turn over the open valve for discharging. Frequently check the tightness of welds, pipes, level gauges, valves and manholes. 3.2 always check the activity of thermometers and pressure gauges. 3.3 check that the safety valve is active and the trap is open. 3.4 overhaul cycle for a year, overhaul of all transmission parts to replace the rolling bearing, should be replaced in a timely manner, add butter lubrication, cover the oil hole. Notice 4.1 when the equipment is out of order, the remaining steam in the tank should be exhausted and can not be repaired under pressure. 4.2 prevent liquid from spilling onto the motor during repair. 4.3 timely cleaning of equipment at end of service.